Category Archives: Remotes

How to Set Up Your Multicode Remote Control for Your Garage

A multi-code remote is a device that helps you open and close your garage door remotely. As a garage owner, having this device will help you save time and all of the hassle of having to do things manually.

The multicode remote control comes along with other added security features to ensure the safety of your garage. Before you start enjoying the benefit that the device comes with here is a step by step guide on how to set up your remote control system.

L1

Discover your remote control

This step is critical and helps you to locate your remote or transmitter.

Test your remote

When setting up the system, to ensure that your remote is functioning well, it is highly recommended that you do the testing at different angles. This will help you ensure that your control system is in a position to communicate well with your door while at a distance.

In the event your remote fails, pressing your wall button will help open it. However, in case the door fails for the second time after pressing the wall button, chances are your operator has issues. If it opens after pressing the wall button it is a good indicator that your radio transmitter has some matters that needs to be fixed.

Locate your radio code

Depending on the manufacturer of your remote control, finding your radio code may be tricky. However, removing your back cover of your receiver or locating dip switches near your receiver’s battery compartment will help you trace the codes very quickly.

L2

Typically your radio codes are switched up. The same codes your radio has should be the same as the receiver and the remote switch statutes. In case they are not similar, you should consider returning your system to your dealer or manufacturer.

Set up your radio code

To set up these codes, you can select the digits by using a screwdriver.

Testing

After setting up your codes and ensuring that the above rules have been followed, now it’s time to test if your new programming works. Before testing, you should also ensure that the removed covers of your receiver and remote have been snapped back. If your garage door opens, you can go ahead and start using your door opener.

In case the devices cannot be synchronized, it is advisable for you to contact your dealer or manufacturer for advice. Always ensure that your remote has been kept in a safe place where no un-authorized parties can have access.

Summing Up

A well programmed multicode remote controlsystem is a worthwhile investment which can help you enhance your security.

Remote Controlled Gates For Convenience And Unbeatable Security!

 linear-act21-250

The discovery of remote control is one of those inventions that has received immence popularity since its introduction to the world. We now have remote controlled TVs, ACs and many more things. However, out of all those indispensable necessaties of human life, one thing that I am going to describe here is remote controlled gates.

Not to mention, remote controlled gates are very popular all across the world due to incredible exclusiveness and extraordinary features of securing prperties. It’s when we talk about security, the very first thing that strikes our mind is the entrance locks as entrance is the key factor for the security of any establishment. This is the place where Act 21A 1 Remote Control comes into place.

Some Top Features Of Act 21A 1 Remote Control Transmitter:

  • Supplied with quick-disconnect key ring
  • Compatible with all Linear access receivers and controllers
  • Factory programmed MegaCode format supports over 1,000,000 codes
  • 1.25″ W x 2.25″ H x 0.48″ D
  • RF frequency: 318 MHz
  • Two type 1616 lithium batteries supplied

How It Works?

The working procedure of a linear Remote Control transmitter can be best understood by the below steps:

  • The device sends a unique code when its button is pressed.
  • The receiver is programmed by “learning” the unique digital code sent by the transmitter.
  • The receiver will identify and activate only from the“memorized” transmitters.
  • The model number is typically printed on the back of the remote.

The functioning concept of Act 21A 1 Remote Control transmitter is not far different from other remote controlled devices. Users just need to press a certain button on a remote to have anything start or stop. When a button is pressed, a specific signal associated with that button is sent to the receiver installed in your gate. As soon as the signal is received, the gate will open automatically. The feature that makes the remote controlled gates more desirable than other alternative security measures is that these gates have battery backups, that is useful when there is a power cut as you are still able to enter your home with the use of remote.

The remote controlled locking systems provide the best security to your home and office structures as no one can open the gate without its remote. No matter how clever tricks and formulas the robbers and burglars may apply to open the gate, all will fall flat as it will stay shut or locked. Hence, there is no chance a thief can break and enter a building secured by a powerful protecting device like Act 21A 1 Remote Control transmitter.

When we talk about security, the first feeling that comes in mind is gate locks as a gate is the main thing to secure any building or place. This is the reason that Act 21A 1 Remote Control transmitter has come in the market that is known to provide unbeatable security as it’s impossible to open a remote controlled gate without its remote.

Linear ACT31B Block Coded 1 Channel Key Ring Remote Control

Linear-ACT31-250

The Linear ACT-31B 1-Channel Block Coded Key Ring Transmitter is designed for use with Linear’s access control products. The Model ACT-31B is a single-channel device supplied with a quick-disconnect key ring. Also included are lithium batteries with a five-year service life. A unique 10-second time-out feature prevents the system from being shut down by a single transmitter transmitting continuously.

The transmitter is MegaCode format, which means each transmitter is factory preprogrammed with one of over 1,000,000 codes, virtually eliminating the possibility of code duplication. Because the receiver ”learns” each specific code, no unauthorized person can gain access to the system by reprogramming a transmitter.
Block coded transmitters are factory programmed to a sequential series of transmitter ID codes. When used with a

Linear access controller, transmitters can be locally or remotely programmed into memory by entering the first and last codes of the block into the system. Facility codes can be selected to further customize the system. FR Frequency is 318MHz

Dimensions are:
1.25″ W x 2.25″ H x .48″ D